[2026] Cisco Troubleshooting and Maintaining Cisco IP Networks (TSHOOT)

문제1

Refer to the exhibit.

R1 can ping the R3 fa0/1 interface Why do the extended pings fail?

A. The DF bit has been set

B. R3 is missing a return route to 10-99.69 0/30-

C. R2 and R3 do not have an OSPF adjacency

D. The maximum packet size accepted by the command is 1476 bytes.

정답: A

문제2

Which of the following are correct statements?

A. EIGRP allows unequal cost load balancing.

B. OSPF requires neighbor adjacencies before updates are sent.

C. OSPF allows unequal cost load balancing.

D. EIGRP uses "cost" to determine best path.

E. EIGRP advertises the best routes to its neighbor.

F. EIGRP advertises all routes to its neighbor.

정답: A,B,E

문제3

Refer to the exhibit.

Which command can be used to apply the INTERNET ACL to an interface in order for traffic to pass?

A. ip access-group INTERNET {in|out}

B. ipv6 traffic-filter INTERNET {in|out}

C. ipv6 access-class INTERNET {in|out}

D. access-class INTERNET {in|out}

정답: B

문제4

The implementation group has been using the test bed to do an IPv6 'proof-of-concept1. After several changes to the network addressing and routing schemes, a trouble ticket has been opened indicating that the loopback address on R1 (2026::111:1) is not able to ping the loopback address on DSW2 (2026::102:1).
Use the supported commands to isolate the cause of this fault and answer the following question.
What is the solution to the fault condition?

A. Under the interface Serial0/0/0.34 configuration enter the ipv6 address 2026::34:1/122 command.

B. Under the interface Tunnel34 configuration delete the tunnel mode ipv6 command.

C. Under the interface Tunnel34 configuration enter the ip address unnumbered Serial0/0/0.34 command.

D. Under the interface Tunnel34 configuration delete the tunnel source Serial0/0/0.34 command and enter the tunnel source 2026::34:1/122 command.

정답: B

설명: (Fast2test 회원만 볼 수 있음)

문제5

Which command displays the RSA public keys of a Cisco router?

A. show crypto session local

B. show crypto key rsa

C. show crypto map

D. show crypto key mypubkey rsa

정답: B

문제6

The implementations group has been using the test bed to do a 'proof-of-concept' that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to isolated the cause of this fault and answer the following questions.
What is the solution to the fault condition?

A. In Configuration mode, using the interface range Fa 1/0/1 - 2, then no switchport port-security interface configuration commands.

B. In Configuration mode, using the interface range Fa 1/0/1 - 2, then no switchport port-security, followed by shutdown, no shutdown interface configuration commands.

C. In Configuration mode, using the interface range Fa 1/0/1 - 2, then no switchport port-security interface configuration commands. Then in exec mode clear errdisable interface fa 1/01 - 2 vlan 10 command

D. In Configuration mode, using the interface range Fa 1/0/1 - 2, then no switchport port-security interface configuration commands. Then in exec mode clear errdisable interface fa 1/0/1, then clear errdisable interface fa 1/0/2 commands.

정답: B

설명: (Fast2test 회원만 볼 수 있음)

문제7

You have 2 NTP servers in your network - 10.1.1.1 and 10.1.1.2. You want to configure a Cisco router to use 10.1.1.2 as its NTP server before falling back to 10.1.1.1. Which commands will you use to configure the router?

A. ntp server 10.1.1.1
ntp server 10.1.1.2 primary

B. ntp server 10.1.1.1
ntp server 10.1.1.2

C. ntp server 10.1.1.1
ntp server 10.1.1.2 prefer

D. ntp server 10.1.1.1 fallback
ntp server 10.1.1.2

정답: C

설명: (Fast2test 회원만 볼 수 있음)

문제8

Refer to the exhibit. The traceroute fails from R1 to R3. What is the cause of the failure?

A. The loopback on R3 is in a shutdown state.

B. An ACL applied inbound on fa0/1 of R3 is dropping the traffic.

C. An ACL applied inbound on loopback0 of R2 is dropping the traffic.

D. Redistribution of connected routes into OSPF is not configured.

정답: B

문제9

Scenario:
A customer network engineer has edited their OSPF network configuration and now your customer is experiencing network issues. They have contacted you to resolve the issues and return the network to full functionality.

The OSPF neighbour relationship has been lost between R1 and R3. What is causing this problem?

A. A neighbor statement needs to be configured in R1 and R3 pointing at each other.

B. The serial interface in R1 should be taken out of the shutdown state.

C. The hello, dead and wait timers on R1 need to be reconfigured to match the values on R3.

D. The R1 network type should be changed to point-to-multipoint non-broadcast.

정답: D

설명: (Fast2test 회원만 볼 수 있음)

Cisco Troubleshooting and Maintaining Cisco IP Networks (TSHOOT) - 300-135무료 덤프문제 풀어보기

우리와 연락하기

유용한 링크

최신 업데이트