[2026] Avaya Ethernet Routing Switch Implementation

문제1

An Ethernet routing switch (ERS) 4550T-PWR has been deployed with a single AC power supply and is currently supporting 20 VoIP telephones with power over Ethernet (PoE). each with a power draw of 8 Watts when offhook.The network engineer has requested the addition of 5 Wireless Access points (WAPs) to the ERS 4550T-PWR.Each WAP supports PoE and requires 12 Watts of power.
What is the outcome of the addition of the WAPs to the ERS 455QT-PWR?

A. The 4550T-PWR will have sufficient power to support the 20 VoIP telephones and 5 WAP devices,

B. The addition of a second AC power supply will be required to provide sufficient power to the ERS -4550T-PWR to Support all of-the PoE devices.

C. the power requirement of the WAP exceeds the individual port maximum power rating of the ERS 4550T-PWR and will therefore require an external power source.

D. The addition of a Redundant Power Supply 15 will be required to provide sufficient power to ensure the VoIP phones and WAP function property.

정답: A

문제2

A technician has installed a license file on the Ethernet routing switch (ERS) 8800 and rebooted, but cannot configure the associated licensed features. it has been determined that license did not load properly at booyup time.
Which two must be verified?

A. The license filename contains valid characters.

B. The switch is at the current release.

C. The license file is stored in the flash directory

D. The appropriate license level has been obtained.

E. The license file has .dat extension.

정답: A,E

문제3

The attempt to manage an Ethernet Routing Switch (ERS) 8600 using a VRRP address was unsuccessful. What is causing this problem?

A. The incorrect MAC offset is configured for the VRRP address.

B. A real IP address is required for management access not a VRRP address.

C. The datacenter interface is set as a critical IP interface.

D. The fie virtual router identifier is 0.

정답: B

문제4

Set of procedures will upgrade the boot monitor on an Ethernet Routing switch (ERS) 8600 with a single 8692SF module?

A. Boot the new image

B. Modify the boot choice for run-time image

C. Copy the new image to flash Modify the boot choice for rim-time image Boot the new image

D. Copy the new image to flash Activate new image with SF module in service

E. Copy the new Image to flash Boot the new image

정답: A

문제5

What is the maximum number of Gigabit Ethernet ports on a single Ethernet Routing Switch (ERS) 8300 Input/Output module?

A. 24

B. 48

C. 50

D. 16

정답: B

문제6

What is the front panel port configuration for the Ethernet Routing Switch (ERS) 2550TPWR?

A. 48 10/100 BaseT ports (PoE on 48 ports) Two combo 10/100/1000BaseT or SFP port

B. 50 10/100BaseT ports (PoE on 25 ports) two combo 10/100/1000BaseT or SFP port

C. 50 10/100BaseT ports (PoE on 50 ports) two combo 10/100/1000BaseT or SFP port

D. 48 10/100BaseT ports (PoE on 24 ports) two combo 10/100/1000BaseT or SFP port

정답: D

문제7

Click on the exhibit button After checking the VLAN configuration using the show vlan info basic and the show vlan info port commands, there are no ACTIVE MEMBER ports for VLM4-50.

What is causing this problem?

A. There are no devices connected to these ports.

B. The ports have not been configured as active for this VLAN

C. The default setting for this type of VLAN is potential and no AppleTalk traffic has entered any of these ports

D. AppleTalk Protocol VLANs do not have ACTIVE MEMBERS

정답: C

Avaya Ethernet Routing Switch Implementation - 6101.1무료 덤프문제 풀어보기

우리와 연락하기

유용한 링크

최신 업데이트