[2026] EMC Dell PowerEdge Professional - DCPPE-200 무료 시험 문제

문제1

An engineer is migrating an existing server node from an M1000E to a VRTX chassis. An error message appears during POST. The system will continue to boot, but can NOT see any of the chassis shared storage or PCIe devices mapped to the server slot. The engineer has already removed the original fabric interfaces in mezzanine slot B and C from the original system configuration.
Which action must the engineer complete to allow the node to see chassis storage and mapped PCIe devices?

A. Install PCIe Pass-Through mezzanine cards

B. Remap chassis storage/PCIe devices

C. Enable PCIe Pass-Through in System Setup

D. Update the CPLD firmware version

정답: C

문제2

Refer to the exhibit.
An engineer is configuring an I/O Aggregator (IOA) for use on a network that has VLANs. The IOA in SLOT A2 is NOT being used currently.
All blades appear to communicate on the network EXCEPT for blades 1b and 1d.
What does the engineer need to do so that blades 1b and 1d can communicate?

A. Add IOM Ports 2, 4, 6, and 8 to the VLANs

B. Configure IOA in A2 for all blades.

C. Install additional network cables for the IOA in A1

D. Set VLANs 10, 20, and 50 to untagged for all ports

정답: A

문제3

Refer to the exhibit.
An engineer needs to configure iSCSI boot on a blade and the iSCSI boot is NOT working.
Which two steps should the engineer take to fix the issue?

A. Modify the boot LUN ID on the target. Validate default gateway settings on the initiator.

B. Verify the IP address of the target and initiator. Validate default gateway settings on the initiator.

C. Update the DNS server entries on the initiator. Change the IQN of the initiator.

D. Change the IQN of the initiator. Verify the IP address of the target and initiator.

정답: B

문제4

An engineer needs to configure a redundant CMC network link into to a newly installed FX2 chassis. CMC port 1 is up and working. The engineer only has one management switch available for CMC connections. The engineer plugs CMC port 2 into the management switch and leaves the data center. The network engineer reports extreme traffic on the network and is unable to connect to any other switches.
How should the engineer fix this problem quickly and maintain redundancy?

A. Add a second stacked management switch and connect CMC port 2 to the new switch

B. Configure the FX2 CMC ports for redundancy in the console

C. Console into the CMC and reset to factory default settings

D. Configure spanning tree on the management switch

정답: A

문제5

AN engineer needs server 1 in the chassis to be able to communicate on the default untagged VLAN 1 and tagged VLANs 10, 20, and 50. The engineer has port 1 configured with the following settings:
interface TenGigabitEthernet 0/1
mtu 12000
switchport
vlan tagged 10,20,50
flowcontrol rx on tx off
During testing, the engineer is unable to communicate with anything on VLAN 1.
How should the engineer fix this issue?

A. Disable all flowcontrol

B. Configure port 1 as a hybrid port

C. Change the default untagged VLAN and tag VLAN 1

D. Set the MTU to default of 1500

정답: D

문제6

An engineer is installing two PCIe NICs into an existing VRTX chassis. Node 1 has three PCIe cards assigned to it already. After installation, the engineer is unable to assign the two new NICs to node 1.
What should the engineer do to assign the two PCIe NICs to node 1?

A. Reseat the NICs

B. Power off the node

C. Upgrade the license

D. Update the CMC firmware

정답: D

문제7

Refer to the exhibit.
An engineer receives a pair of the modules shown to install into a pair of MXL switches.
Which cables does the engineer need for this module?

A. Cat6A Snagless Unshielded (UTP) Network Patch Cable

B. OM4 MTP Crossover Fiber Cable (optics required)

C. QSFP+ to QSFP+, 40GbE Passive Copper Direct Attach

D. SFP+ to SFP+, 10GbE, Copper Twinax Direct Attach

정답: C

문제8

An FX2 has one compute node and three storage needs. The server sees only half of the drives in the FD332 in SLOT 3. The chassis needs to be configured to see all drives in all storage nodes. What should an engineer do to accomplish this task?

A. Enable shared storage in the CMC

B. Set storage mode to single PERC/joined

C. Enable clustering in the CMC

D. Set storage mode to single host

정답: B

문제9

An engineer is trying to use OpenManage Essentials to automate the deployment of 100 bare metal servers.
The engineer purchased the OME - Server Configuration Management license after point of sale and now has all of the licenses needed.
What is the most efficient way to install the licenses?

A. using CMC

B. using OpenManage Essentials

C. using a script

D. using Dell License Manager

정답: D

문제10

An engineer is redeploying a blade chassis, and is logged into the CMC web interface. The engineer has configured the iDRACs for the blade servers.
When the engineer tries to log into one of the iDRACs, the connection fails. The engineer can ping the CMC from the engineer's workstation but can NOT ping the iDRACs. The engineer tries to ping the iDRAC IP from the CMC itself using the diagnostic tool, but that also fails.
Which two tasks should the engineer perform? (Choose two.)

A. Disable firewall service on iDRAC

B. Update DNS servers for iDRAC

C. Check VLAN settings on the CMC and iDRAC

D. Confirm subnet mask configuration on iDRAC

E. Enable IPv6 on the CMC and iDRAC

정답: A,D

EMC Dell PowerEdge Professional - DCPPE-200무료 덤프문제 풀어보기

우리와 연락하기

유용한 링크

최신 업데이트