[2026] Dell SC Series Storage Professional - DSDSC-200 무료 시험 문제

문제1

An engineer needs to install an LSI9206 SAS card in an existing SC8000 system that runs version 6.1.
Which step should the technician take to install this IO module?

A. As a hot-add card, install the card in any slot without powering down the controller.

B. Update the SCOS to version 6.3 because this is the minimum version for this card to run.

C. Download the LSI 9206 firmware from the Compellent portal to apply to the card.

D. Make sure that slots 1, 2, or3 are available because the card can NOT be installed in a full-height slot.

정답: C

문제2

A client needs On Demand Data Progression to immediately move data from Tier 1 to Tier
2 when a replay is taken.
After enabling manual mode, which two attributes should the technician assign to a custom storage profile to meet this requirement? (Choose two.)

A. Tier 2 - RAID 5/6 Replay

B. Tier 2 - RAID 5/6 Writes

C. Tier 1 - RAID 10 Writes

D. Tier 1 - RAID 10 Replay

정답: B,C

문제3

Ail engineer has several servers connected to the Storage Center through two FC fabrics.
The Storage Center runs m Legacy mode. The engineer needs to create zones based on
World Wide Names (WWN).
Which WWNs from the Storage Center need to be included in the zone with the server
WWN?

A. only the Virtual WWNs

B. only the Primary WWNs

C. both the Primary and Reserve WWNs

D. both the Virtual and Physical WWNs

정답: C

문제4

The engineer notices that iSCSI servers are NOT performing as expected. After reviewing the graphics, the engineer identifies high latency due to an excessive number of retransmits. What is causing the performance issue?

A. Switch firmware is out of date.

B. Flow Control is disabled.

C. A VLAN ID value is set on the properties of the server NT

D. The system uses the standard MTU size.

정답: C

문제5

A Storage Center runs in Legacy Port mode.
How should the Storage Center zone(s) be set up?

A. All reserve port WWNs should be in one zone and all primary port WWNs in another zone.

B. All Storage Center WWNs should be in one zone-

C. The server WWN should be in one zone.

D. All physical port WWNs should be in one zone and all virtual port WWNs in one zone.

정답: A

문제6

A technician needs to perform a SCOS version update via ISO to an SC8000. The technician needs to connect to the controller with a web browser to the iDRAC IP address.
What are three ways that the technician should use to obtain the iDRAC IP address?
(Choose three.)

A. view LCD Panel on the Front of Controller

B. Use serial connection to the controllers (CLI)

C. open the Controller Properties with the Storage Center System Manager

D. open the configuration Settings Wizard under System Properties within the Storage
Center System Manager

E. open the iDRAC Configuration Properties within the Storage Center System Manager

정답: A,B,C

문제7

An engineer wants to perform a Storage Center OS ISO update, but must determine the
BMC IP address first In what two ways can the engineer determine the BMC IP address?
(Choose two )

A. From the Dell Storage Manager Data Collector, choose the Storage Centers tab and find the BMC IP address for each controller.

B. Do trace route from the controller command line interface to the virtual IP The second to last hop to die destination is the BMC IP address.

C. From the command line interface of each controller, run "platform bmc show"

D. In Dell Storage Manager client, highlight the controller under the Hardware tab and choose "Edit Setrings".

정답: C

문제8

During a Storage Center dual-controller upgrade from SC030 to SC8000, the onsite engineer fails to reload the configuration to flash on a controller.
What is the result?

A. fibreswitch segmentation

B. engineer must manage new disks

C. unavailable data

D. controller comes up as 'new system'

정답: D

문제9

An engineer needs to create a volume in the web GUT Explorer view. The volume needs to automatically present to a specific server when created. How should the engineer create this volume?

A. right-click on the Storage icon and select Create volume

B. right-click on the Storage icon and select Create volumes

C. right-click on the Servers group icon and select Create volume

D. right-click on the intended server and select Create volumes

정답: D

문제10

A site contains many volumes that are all listed under the Volumes icon. These volumes are mapped to several servers. The engineer needs to be able to more easily manage the volumes for replay scheduling. The engineer does NOT want to duplicate any work when assigning the volumes to a replay profile
How should the engineer accomplish the task?

A. create replications for each volume and use the Active Replay option- then assign the replicating volumes to the replay profile

B. create the replay profiles and assign the volumes individually to each profile

C. create storage profiles, add the volumes to the storage profile. then assign the storage profile to the replay profile

D. create volume folders and move the volumes into them, then assign the volume folder to the desired replay profile

정답: D

Dell SC Series Storage Professional - DSDSC-200무료 덤프문제 풀어보기

우리와 연락하기

유용한 링크

최신 업데이트