[2026] Network Appliance NetApp Certified Storage Installation Engineer, ONTAP

문제1

Config Advisor reports that you have a single point of failure on a stack of shelves. After investigation, you have assigned the following ports to each stack:
stack 1 - ports 0a and 0b
stack 2 -ports 3a and 4b
stack 3 - ports 4a and 3b
In this scenario, which two changes would you make to the cabling to solve the problem? (Choose two.)

A. Cable stack 3 to ports 4a and 0b.

B. Cable stack 1 to ports 0a and 3b.

C. Cable stack 2 to ports 4a and 4b.

D. Cable stack 3 to ports 3a and 3b.

정답: B,C

문제2

You are dispatched to install a new cluster with six AFF A300 nodes. While running Config Advisor, you determine that there is a newer firmware version for 48 SSDs.
Which statement is correct in this scenario?

A. Prior to leaving the site, tell the customer that a later firmware exists for those disk drives, but that the upgrade will provoke downtime.

B. Prior to leaving the site, advise the customer that the firmware is included in the version of ONTAP that they downloaded.

C. Unless the customer advises otherwise, leave the firmware alone and document the version of ONTAP being used to explain the issue.

D. Unless the customer advises otherwise, upgrade the firmware on the SSDs to clear the Config Advisor error.

정답: B

문제3

A customer wants to reduce the task allocation requirement for the root aggregate and increase usable storage by partitioning the disks into one large part and one small part. The small part is used for the root aggregate and the large part for the data aggregates?
In this situation, what is this feature called?

A. ONTAP

B. storage virtual machine

C. RAID

D. Advanced Drive Partitioning

정답: D

문제4

Which two statements are true about the ONTAP 9.5 networking features.

A. The MTU will be the same across all ports in a broadcast domain.

B. The broadcast domain is a layer 3 object.

C. The MTU will change based on each port configuration ion broadcast domain

D. The broadcast domain is a layer 2 object.

정답: C,D

문제5

According to NetApp best practices, how many NTP servers should you associate with an ONTAP cluster?

A. 2

B. 3

C. 1

D. 4

정답: B

문제6

What is the main function of ACP?

A. It allows the controller to use Ethernet instead of SAS to fetch the storage data.

B. It allows the controller to nondisruptively reset the SAS expanders.

C. It allows cabling the shelf to two additional controllers.

D. It enables the automatic shelf ID assignment.

정답: A

문제7

You install a new FAS26xx HA system with ONTAP 9.5 at a customer's site. After cabling the SAS cables, the customer wants to cable Alternate Control Path (ACP). But the FAS26xx has no physical port for ACP.
Which statement is correct in this scenario?

A. The ACP function is established over the customer network.

B. Within a FAS HA system, the ACP function is established over the cluster interconnect

C. To reach the ACP function, you should put the ACP cable into one of the onboard Ethernet pons.

D. Beginning with ONTAP 9 software. ACP cabling for disk shelves is no longer required.

정답: D

문제8

Which statement regarding Epsilon is true?

A. Whenever a new node is added, the epsilon is automatically reassigned to this node.

B. Epsilon is reassigned automatically to the HA partner in case the current owner of the epsilon suddenly reboots.

C. The epsilon acts as a tiebreaker in a 2-node cluster.

D. The node holding the epsilon has extra fractional vote weight.

정답: D

문제9

What are two types of load balancing methods available in multimode interface groups? (Choose two.)

A. LIF-based load balancing

B. broadcast domain-based load balancing

C. IP-based load balancing

D. port-based load balancing

정답: C,D

문제10

You have just completed the installation of a FAS9000 HA pair with ONTAP 9.5.
In this scenario, according to NetApp best practices, which two tests verify the HA failover functionality?
(Choose two.)

A. Invoke a system core.

B. Pull the motherboard out of the slot.

C. Disconnect the HA interconnect cabling.

D. Power cycle the node.

정답: A,D

문제11

A customer has recently purchase a new ONTAP 9.0 storage system and wants you to join the nodes to an existing cluster running ONTAP 9.5.
What is the first step for adding the new controllers to the existing cluster?

A. You must configure the existing cluster to accept the Joining nodes.

B. You must make sure that there Is the same amount of disk shelves attached to all nodes.

C. You must match the operating system.

D. You must ensure that all network switches are upgraded and online.

정답: C

Network Appliance NetApp Certified Storage Installation Engineer, ONTAP - NS0-182무료 덤프문제 풀어보기

우리와 연락하기

유용한 링크

최신 업데이트