[2026] Network Appliance NetApp Certified Implementation Engineer - SAN, Clustered Data ONTAP

문제1

Click the Exhibit button.
cl01::>iscsi portal show
Logical Status CurrCurr
Vserver Interface TPGT
Admin/Oper IP Address Node
Port Enabled
---------- ---------- ---- --
-------- ---------------- ----
------- ---- -------
svm1 1-a 1035 up/up
192.168.1.66 cl01-01 e0a true
svm1 1-b 1051 up/up
192.168.1.67 cl01-01 e0b true
svm1 2-a 1046 up/down
192.168.1.68 cl01-02 e0a true
svm1 2-b 1052 up/up
192.168.1.69 cl01-02 e0b true
Referring to the exhibit, which action would you take to troubleshoot the iscsi-2-a interface?

A. Verify network connectivity between the host and LIF.

B. Verify that the iSCSI protocol is started on svm1.

C. Cycle the upstream switch port down and back up again.

D. Verify that the iSCSI protocol is licensed for svm1.

정답: C

문제2

A customer has recently deployed a clustered Data ONTAP 8.3 system and is trying to mount LUNs to a Windows 2012
Server using the iSCSI protocol. They are using Cisco Nexus 5548 network switches and the network administrator has
informed the storage administrator that the ports are set to switchport mode trunk. The storage administrator has
also been informed that the host and storage should be using VLAN 400 for iSCSI traffic. When the storage
administrator attempts to add the SVM as an iSCSI target, it fails to connect.
What is causing the problem?

A. Windows 2012 Server does not support the iSCSI protocol on a VLAN tagged interface.

B. Clustered Data ONTAP 8.3 does not support running iSCSI on a VLAN ID below 1024.

C. The storage administrator has not enabled VLAN tagging on the storage ports.

D. Clustered Data ONTAP 8.3 does not support the iSCSI protocol on a VLAN tagged interface.

정답: C

문제3

Click the Exhibit button.
cl01::>lun resize -vserver
svm1 -volume db1_vol -lun db1
-size 4096g
Error: command failed: New
size exceeds this LUN's
initial geometry
cl01::>
What is the reason for the error shown in the exhibit?

A. The aggregate over commitment threshold has been exceeded.

B. The LUN cannot be grown past its maximum resize size.

C. The LUN is thin provisioned, but the parent volume is thick provisioned and cannot satisfy the request.

D. The parent volume that contains the LUN is out of space.

정답: B

설명: (Fast2test 회원만 볼 수 있음)

문제4

Click the Exhibit button.

A customer has deployed a new FAS8080EX running clustered Data ONTAP 8.3. Host A is running multipath software
that has been properly configured. Also, Host A is currently accessing a LUN using the FC protocol stored on Node

A. Switch A, shown in the exhibit, fails.
What will happen next?

B. Host A will continue to access its LUN using Switch B through Node B.

C. Node A will panic causing a storage failover to Node B.

D. Host A will continue to access its LUN using Switch B through Node A.

E. Host A will lose all access to its LUN.

정답: E

문제5

A new server has been installed in your environment, but it is unable to see its NetApp boot LUN. You have narrowed
the problem down to the zoning on your Cisco switch which has the following configuration:
zone name z_NetAppvsan 400
memberpwwn 20:00:00:25:b5:c0:ff:ee
memberpwwn 50:0a:09:84:8d:7c:51:d5
zoneset name zs_NetAppvsan 400
memberz_NetApp
zoneset activate name zs_NetAppvsan 400
What is the problem with your zoning configuration?

A. The zone and zoneset names do not match.

B. The member does not reference the VSAN.

C. The zoneset was improperly activated.

D. The PWWN for your NetApp LIF is incorrect.

정답: D

문제6

Click the Exhibit button.
cl01::>ucadmin show
Current Current Pending
Pending Admin
Node Adapter Mode Type Mode
------------- ------- -------
--------- -------- --------- -
----------
cl01-01 0c fc target - -
online
cl01-01 0d fc target - -
online
cl01-01 3a cna target - -
online
cl01-01 3b cna target - -
online
cl01-01 4a cna target - -
online
cl01-01 4b cna target - -
online
cl02-01 0c fc target - -
online
cl02-01 0d fc target - -
online
cl01-02 3a cna target - -
online
cl01-02 3b cna target - -
online
cl01-02 4a cna target - -
online
cl01-02 4b cna target - -
online
12 entries were displayed.
cl01::>
Referring to the exhibit, which cables are valid for connecting port 0d on node cl01-02 when the switch is 10 meters
away?

A. Twinax copper SFP+ active cables

B. LC/LC optical OM3 cables

C. Twinax copper SFP+ passive cables

D. RJ45 Cat6 Ethernet cables

정답: C

문제7

What does Selective LUN Mapping (SLM) do?

A. It allows the administrator to automatically create LUNs using SnapDrive for Windows and SnapDrive for UNIX.

B. It makes a LUN accessible only through paths on the node owning the LUN and its HA partner.

C. It allows the node and its HA partner to create zones on the SAN fabric to automate LUN mapping.

D. It automates igroup creation.

정답: B

설명: (Fast2test 회원만 볼 수 있음)

문제8

A company has a 4-node Data ONTAP cluster called cl01. The administrator attempts to create a volume on svm1 and
can only select aggregates that are owned by node cl01-01 or cl01-02.
What is causing the problem?

A. Volume creation delegation is not configured to allow use of cl01-03 or cl01-04 owned aggregates.

B. No LIFs have been created on nodes cl01-03 or cl01-04.

C. The SVM peering relationship has not been configured with the cl01-03 and cl01-04 HA pair.

D. The storage virtual machine is not configured to use nodes cl01-03 or cl01-04.

정답: D

Network Appliance NetApp Certified Implementation Engineer - SAN, Clustered Data ONTAP - NS0-506무료 덤프문제 풀어보기

우리와 연락하기

유용한 링크

최신 업데이트